Typ:
EGR15U4000C
Č. výrobku:
5-001521
Upozornenie
Rail in manufacturing length, please note the deviating tolerance specifications in the table.
Dimensions
| Rozměry | |||
|---|---|---|---|
| WR | Šířka kolejnice | 15 | mm |
| HR | Výška kolejnice | 12,5 | mm |
| D | 7,5 | mm | |
| h | 5,3 | mm | |
| d | 4,5 | mm | |
| P | Rozteč otvorů | 60 | mm |
| Lmax | Max. délka (E1 = E2 = P/2) | 3900 | mm |
| Lmin | Minimální délka | 72 | mm |
| E1/2 min | 6 | mm | |
| E1/2 max | 54 | mm | |
| Hmotnost | 1,23 | kg/m | |
| Rozměr (kolejnice ve výrobní délce) | |||
|---|---|---|---|
| L | Celková délka | 4.000 +20 | mm |
| E1 | 20 ±0,5 | mm | |
| E2 | 20 +20 | mm | |
Povlakování HIWIN HICOAT CTS
HICOAT CTS je tenkovrstvé chromování, které poskytuje dobrou ochranu proti korozi a velmi dobrou ochranu proti opotrebení. Vysoká odolnost proti opotrebení je dusledkem velmi vysoké tvrdosti povlakování. Povlakování CTS neobsahuje Cr(VI) a je bezpecné pro potraviny. Je k dispozici pro výrobní rady HG, EG, CG a WE. Další informace jsou uvedeny v katalogu „Lineární vedení“ v kapitole „Povlakování HIWIN pro lineární vedení“.
HIWIN coating HICOAT CZS
HICOAT CZS is a very thin zinc coating that offers a very good corrosion protection, even on radii and chamfers. Smaller bare parts stay protected by the cathodic corrosion protection. Compared with uncoated pieces this leads to significantly higher periods of use. The CZS coating is available for the HG, EG and CG series. Further information can be found in the catalogue "Linear Guideways" under chapter "HIWIN coatings for linear guideways".
| Označenie | Kategória | Výrobok | Veľkosť | Jazyk |
|---|---|---|---|---|
| Linear guideways | Assembly Instructions | Linear guideways | 4 MB | |
| Linear guideways | Project planning sheet | Linear guideways | 2 MB | |
| Linear guideways | Catalogue | Linear guideways | 7 MB | |
| CG linear guideways | Flyer | Linear guideways | 299 KB |
Principle of operation of a linear guideway
A linear guideway makes it possible to move in a linear motion with rolling elements. The use of balls and rolls between the rail and block in a linear guideway makes precise linear movements possible.
Displacement resistance depending on lubrication condition
The displacement resistance of a carriage depends on many factors, e.g. load, temperature, lubricant (grease, fluid grease, oil), lubricant quantity, travel speed, series, size or the sealing system. A concrete specification of the displacement resistance is therefore only possible with defined general conditions. An essential factor here is the lubricant and the lubrication condition. Especially in freshly lubricated condition, the displacement resistance is clearly increased. However, after a running-in period of 15 metres, the displacement resistance is reduced again by approx. 50%.
Mechanical or manual chamfering
In the following video, you can see how chamfering edges on linear guideways works both mechanically and manually.
Long-time lubrication unit of a linear guideway
The long-time lubrication unit for linear guideways makes it possible to increase lubrication intervals many times over, thereby considerably reducing the number of maintenance intervals. If needed, up to two long-time lubrication unit can be installed per block.
Assembly and disassembly of cover caps
The cover caps are used to keep the mounting holes of the profile rails free of chips and dirt. In this video, we show you how to easily assemble and disassemble steel, brass or plastic cover caps.